Sheri Mortimer asked 1 year ago
How to Change a Subaru Spare Key
If you’ve lost your Subaru car key, call a locksmith. Usually, they will cut an alternative key for you much less expensively than the dealer.
Fob remote “push to start” intelligent keys or a plain metal key are the two most commonly used kinds of Subaru car keys. The Fob keys have an embedded chip and requires reprogramming.
Keyless Entry System
The key fob can be used to lock and unlock your Subaru remotely. It also opens the trunk of your vehicle or the lift gate. These remotes are connected to a keypad inside your car to connect with your computer system of your vehicle.
Some models of Subaru come with a lesser-known feature called PIN Code Access. This allows you to make a unique number sequence to open and start your vehicle. Go through the owner’s guide to learn how to utilize this feature if you own a Subaru Forester, Outback Crosstrek, WRX STI or Impreza.
It’s possible that the battery inside the key fob has died. The first thing you’ll want to check is that it’s got new batteries and you can do this using a handheld remote tester or a basic multimeter in your home garage.
Next, you’ll want to take the key fob out of its case and look at the circuit board that controls the transmitter. This will have one or two sets of eight-digit numbers, so note down the first set so you will be able to remember it later. After you’ve done this, you can begin programming your key fob at home. The procedure to do this will vary based on the type and year of your car but it’s generally simple enough to do by yourself.
Key Fobs
Subaru’s newest models are all equipped with key fobs that don’t just unlock the doors however, they also activate your lights, lock the gas cap, and start your vehicle. This last trick is particularly helpful if you’ve been at the gas station only to find that your car won’t start because the battery in the key fob has died.
If your Subaru is new or older it’s likely that your key fob can be replaced with little difficulty. It’s important to note that newer models with an advanced level of technological sophistication could require an excursion to the dealer. However, with a little time and effort, you can get your replacement key fob in place at home.
Begin by looking at the circuit board that controls the transmitter on your key fob (instructions to open the case must be included in your owner’s handbook). It should contain one or two sets of serial numbers each one of which is 8 digits long. Write down the initial number series and keep it in a safe place for reference later on.
After that, get in your driver’s seat and close all the doors. Turn the key to start the vehicle, then turn off after 10 turns. Press the lock button of your key fob, hmsysmd.snu.ac.kr and then open the door. This will test that your doors are working correctly. Close the door, and then remove the key. You should hear the chime from your vehicle, signaling that the key fob is programmed.
Ignition System
The key battery may be dead if your Subaru keys aren’t working as they should. You can replace the key fob battery at home if you know how. A replacement battery is not expensive and easy to locate. If your keypad doesn’t respond to your commands, it could be a different issue. To find a spare key, it’s advisable to visit an authorized dealer. They’ll ensure that the key is genuine Subaru key, which is covered under warranty, and is programmed to your vehicle. This is much safer and easier than buying an aftermarket key from an organization on the internet.
You can also have the dealer cut a new key if they are provided with your VIN and proof of ownership. This information is used to code the key replacement so that it can be accepted by your immobilizer. This is a more intricate process than cutting a single key, and the dealer will charge you more.
Once the new key is programmed, you are able to switch it with your working key. It takes just five seconds to insert the new key, so keep your working key close at fingertips. When the security light stops flashing, you can remove the new key and examine it to make sure it’s functioning properly.
Battery Replacement
One of the most important features that make Subaru fobs useful is their ability to switch on your car’s power windows and sunroof by pressing of the button. The battery in your Subaru fob isn’t intended to last forever, and will require replacement at some point. It’s good news that replacing the battery is a simple procedure that you can do yourself with the help of this simple guide from Capitol Subaru.
You’ll need to locate the small crevice that separates the front and back of your keyfob. With a small flathead screwdriver, you can pop the seam to reveal a small area inside that houses the battery. Install the new battery and ensure it is facing correctly. Remove the old one. Once you’ve assembled everything, you can use the new key fob to lock, unlocking, and starting your vehicle.
It’s always best to have an additional set of keys available in case you’ve lost yours or not working properly. A new key can be purchased at your local auto dealership or you can request one made by locksmiths. It is important to ensure to ensure that your key works efficiently as soon as you can so that you can safely drive.